DIVISION ONE

Division 1 Rules:

To apply for this class your RC must meet these requirements to be eligible. Understand these rules may and can be changed without notice.

Division 1

The spirit of this class is daily driven trucks, with mild modifications/lift. Keep that in mind when building.

1/10th scale only

BODY:

• All bodies must be made of - Wood/Metal/ABS/Styrene/3D Printed materials, No lexan at all.

• If your body is molded into one piece you don't have to separate the bed from the cab. 

• Full drop beds are required for trucks with a minimum depth of 1" unless you run a Flatbed. Flatbeds can be made of Wood/Metal/ABS/3D Printed materials. The flatbed must be at least as wide as the cabs widest point

• All bodies/beds must cover entire chassis

• All bodies need a full windshield and full rear window

• No dovetailing

• Bobbing the bed is allowed. From rear inner fender to tailgate can’t be shorter than an 1 ½” The RC4WD Marlin bed is the template, base your bobbed bed off that. 

• No Front fender pinching

• Front/Rear Fenders must cover 90% of your tire,

• Fender Flares are allowed.

• No Fender trimming allowed unless you are running fender flares, then wheel wells can be trimmed only to match the fender flares which need to cover the entire fender. 

• Fender Flares must be used for the make they are made for, for example, no Jeep/Willy's shaped fenders for your Chevy Truck so you can cut the wheel wells to that shape. 

• No cages/tubes can be used for chassis

• No Honcho/Ascender molded beds allowed

• 3D printed bodies are allowed but must replicate a 1:1 Manufacturers body, ie Chevy, Ford, etc.

**exception 1 - if you have a scratch built body made of wood/metal/styrene and they fit the measurement requirements and look like a 1:1 style body we will allow them in this class if all other rules are met.****As long as your body serves nothing more than looks, ie If your body is weathered, rusted, beat, and or just built to "look" a certain way, we will take that into consideration when you tech in.** 

BUMPERS:

• Front and Rear bumpers must be attached to their appropriate locations on the chassis or body depending on mounting application. 

• Stock/homemade/aftermarket bumpers must cover the entire nose and rear of the body fender to fender aka Full Width Bumpers

• Aftermarket Bumpers must be ahead of your body. No even or under the body bumpers allowed. 

• If the stock bumper is molded into the body, no additional bumper is required. 

INTERIOR:

**interior must resemble the stock interior of the 1:1 make you are building**

• Full 3D interior's are required

• Molded interiors in bodies, like New Bright, must adhere to the scale guide lines but are accepted as 3D interiors.

• Roll bar/headache bar is a must for open roof bodies, ie Jeep, 4Runner, Blazer, Bronco, etc. If using a cap, no need for a roll bar.

• Scale Drivers must be no smaller than 5.5" and MUST resemble a human figure.

• All interiors must be deep enough for your scale drivers to be whole from the knees up.

SUSPENSION:

• Shocks must be no longer than 90mm

• Cantilever suspension is allowed on the rear only

• Steel Leaf springs only

• No Delrin/3D printed/Plastic leaf springs allowed

CHASSIS:

• Factory RTR/Kit chassis ONLY

• No cutting the chassis’ original length

• No half chassis

• No truggies

• No TVP

TIRES:

• Max tire size - measured physical size must not exceed 4.19"

• Scale style tires

• No cut, shut, comp tires allowed 

• No trimming treads allowed

• No sipping allowed 

• NO TIRE MODIFICATIONS AT ALL!!!!!

• Front and rear tires must be in the fender wells. No stretched wheelbases past the fender wells.

WHEELS:

**1.55's, 1.7’s 1.9's will run in the same divisions.**

• No stretching tires over wheels. 

• No visual wheel weights allowed 

• No weights on axles

• No weighted brake rotors

AXLES:

• Factory RTR/Kit axles

• Axles must be shaft driven

• Approved 3D Printed axles:

  • Bowhouse RC NCYota 152/170mm

  • Bowhouse NC60

  • GCM TM8 TMX

• Officially Licensed 1:1 replica Axle’s allowed

• Axles not allowed - Portals, Worm gear, RC4WD Blackwells

• Absolutely zero visible weight is allowed on any part of the axle or steering components. No brass, steel, lead weights etc,

• No Knuckle weights

• No weighted disc style brakes

• Inner axle tubes are the only exception 

• Axle width must be no longer than 9.5" from axle end to axle end

• No MOA

ELECTRONICS:

• All electronics and wires Must be hidden.Excluding wires for external illumination devices and winches. 

MISC:

• No dig

• No rear steer

• No free gear shift

• Servo winch is allowed. The winch cable MUST come through the front bumper with a fairlead. 

• A scale replica winch is allowed

• No servo on axles

Mandatory items:

• Driver

• Windshield Wipers

**If you don't know or assume something is allowed, just ask, and we can let you know, or we can just put you in a different division.**